Bissell Hot Beverage Maker 29H3 User Manual

Earn BISSELL Rewards!  
Register your  
product today!  
See details on  
back page  
USER'S GUIDE  
53Y8, 29H3, 75Q3 SERIES  
2
3
Thank You  
Safety Instructions  
Product View  
4
5
Assembly  
5-6  
Operations  
6-8  
9-10  
10  
Maintenance and Care  
Troubleshooting  
Replacement Parts  
11  
12  
12  
Warranty  
Product Registration  
Consumer Services  
 
IMPORTANT SAFETY INSTRUCTIONS  
When using an electrical appliance, basic  
precautions should be observed, including  
the following:  
Keep hair, loose clothing, fingers, and all  
parts of body away from openings and  
moving parts.  
Use extra care when cleaning stairs.  
Read all  
Do not pick up flammable materials  
(lighter fluid, gasoline, kerosene, etc.) or  
use in the presence of explosive liquids  
or vapors.  
Always turn off this appliance before con-  
necting or disconnecting the motorized  
nozzle.  
instRuctions  
befoRe using youR  
VacuuM.  
WaRning: to  
reduce the risk of fire,  
Do not pick up toxic material (chlorine  
electric shock, or injury:  
bleach, ammonia, drain cleaner, etc.).  
Do not use outdoors or on wet surfaces.  
Do not use vacuum cleaner in an  
enclosed space filled with vapors given  
off by oil base paint, paint thinner, some  
moth proofing substances,  
Do not allow to be used as a toy.  
Close attention is necessary when used  
by or near children.  
Do not use for any purpose other than  
described in this User’s Guide.  
Use only manufacturer’s recommended  
attachments.  
flammable dust, or other explosive or  
toxic vapors.  
Do not pick up hard or sharp objects  
such as glass, nails, screws, coins, etc.  
Do not pick up anything that is burning  
or smoking, such as cigarettes, matches, or  
hot ashes.  
Do not use with damaged cord or plug.  
If appliance is not working as it should,  
has been dropped, damaged, left out-  
doors, or dropped into water, have it  
repaired at an authorized service center.  
Do not pull or carry by cord, use cord as a  
handle, close a door on cord, or pull cord  
around sharp edges or corners. Do not  
run appliance over cord. Keep cord away  
from heated surfaces.  
Do not unplug by pulling on cord. To  
unplug, grasp the plug, not the cord.  
Do not handle charger, including charger  
plug and charger terminal with wet hands.  
Do not use without dust cup or filters in  
place.  
Use only on dry, indoor surfaces.  
Keep appliance on a level surface.  
saVe tHese  
instRuctions  
foR futuRe use  
This model is for household use only.  
Do not charge the unit outdoors.  
Use only the charger supplied by the  
manufacturer to recharge.  
Do not incinerate the appliance even if  
it severely damaged. The batteries can  
explode in a fire.  
Do not put any object into opening.  
Do not use with any opening blocked.  
Keep openings free of dust, lint, hair and  
anything that may reduce airflow.  
3
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Product view  
Power/Brush roll  
On/Off  
2-Way Folding  
Handle Release  
Hand Vacuum  
Release  
Dirt Cup Release  
Detachable  
Hand  
Vacuum  
Filter  
Dirt Container  
Charging Adapter Plug  
Integrated  
Crevice Tool  
caution:  
Swivel Head  
Do not plug in your vacuum  
cleaner until you are famil-  
iar with all instructions and  
operating procedures.  
4
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Assembly  
no tools are required for assembly;  
simply insert foot into body of unit until  
you hear a click.  
charging  
before charging, make sure unit is in  
the off position.  
1. Insert the charging adapter plug into the  
charging port on the back of the unit.  
2. Plug the adapter into the wall outlet. The red  
indicator light will illuminate and remain on  
when plugged into wall outlet. Charge the  
unit completely for 24 hours prior to first use.  
1.  
note: the adapter may become warm  
during charging this is normal.  
3. When the unit is fully discharged, approx-  
imately 16 hours of charging is required  
for the battery to regain full capacity.  
Operations  
Power switch  
the power switch is located on the top of  
the handle. settings include:  
(o) = off  
(i) = suction on  
(bRusH) = suction and brush on  
using your stick vacuum  
1. Push power switch on to desired setting.  
2. Easily clean hard floors, low pile carpet,  
and area rugs.  
3. When finished cleaning, turn power  
switch to OFF (O) position.  
2-way folding handle  
for cleaning under couches, beds and  
other hard to reach areas.  
1.  
2-Way Folding  
Handle Release  
1. To release, push button located under  
power switch to bend handle forward for  
cleaning under furniture.  
2. For space saving storage, push button to  
bend handle backward.  
5
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Operations  
cleaning with the detachable hand vac  
1. Remove hand vac by pressing the release  
button.  
1
2. Power switch is located under handle and  
should be depressed while cleaning is tak-  
ing place.  
Power Switch  
3. Easily clean messes on furniture, stairs,  
and other hard to reach areas.  
4.  
5.  
4. For hard to reach messes, use the  
integrated crevice tool. To access crevice  
tool, pull on tab indicated by arrow on  
front of hand vac nozzle. Listen for click to  
know crevice tool is ready to use.  
5. When done cleaning, simply push crevice  
tool back into unit.  
Maintenance and care  
to maintain maximum cleaning perfor-  
mance, the following maintenance steps  
must be performed:  
emptying the dirt cup  
dirt cup should be emptied before  
debris reaches the full line on cup.  
1. Turn power OFF (O) and remove hand  
2.  
3.  
vacuum from unit, as directed in step 1  
"Cleaning with the detachable hand vac".  
2. Hold hand vacuum vertically and depress  
the release button to release dirt container.  
3. Gently pull dirt container away from the  
hand vacuum grip and remove the filter.  
Empty dirt into waste container.  
4. Replace filter back into the dirt container  
and attach dirt container to hand vacuum  
until it snaps securely in place.  
cleaning or Replacing the filter  
the key to maximum performance is  
having a clean filter. cleaning the filter  
after each use will help your vacuum  
operate at peak efficiency.  
6
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Maintenance and care  
cleaning or Replacing the filter continued  
use only genuine bissell replace-  
ment filters in your bissell vacuum.  
to purchase visit WWW.bissell.coM  
or call 1-800-237-7691.  
To clean filter:  
1. Turn power OFF (O).  
2. Remove the dirt container from the hand  
vacuum, as directed in step 1 "Emptying  
the dirt cup" on page 6.  
3. Remove filter and tap firmly against the  
3.  
4.  
inside of a waste container, removing  
any visible dirt.  
4. Replace filter back into the dirt container  
and attach dirt container to hand  
vacuum until it snaps securely in place.  
NOTE: After heavy usage, you may  
clean the filter by washing it gently  
by hand in warm water and mild  
dish detergent. Rinse thoroughly  
and make certain it is completely  
dry before replacing it.  
brush roll and brush roll belt maintenance  
the brush roll may accumulate debris  
such as strings, hair and fibers. this  
type of debris can wrap around the  
brush and diminish its ability to clean  
effectively.  
To remove brush roll for cleaning:  
1. Turn power OFF (O). Remove foot  
2.  
assembly from unit and turn over to  
access the brush roll.  
2. Remove three Phillips head screws to  
remove the belt cover.  
3. To remove brush roll, pull on the brush  
near the belt side. Clean off hair or  
other debris from brush roll.  
4. Place cleaned brush roll back into foot  
of unit by aligning the non-belt side so  
it's seated in the nozzle.  
3
5. Pivot the brush roll so the belt end slides  
into the slot in the nozzle.  
6. Replace the belt cover and secure with  
three screws. Attach foot assembly  
on unit.  
7
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Maintenance and care  
brush roll and brush roll belt maintenance continued  
Brush roll reset:  
if larger debris becomes lodged in the  
foot of the unit and the brush roll shuts  
off, turn the unit off and remove the  
obstruction. Wait approximately 15 sec-  
onds for the motor to cool down before  
turning back on. brush will function  
again after allowing time to cool down.  
Brush roll belt replacement:  
if the brush roll belt should break,  
call 1-800-237-7691 or visit WWW.  
bissell.coM to purchase replacement  
belt.  
Replacement instructions:  
1. Turn power OFF (O). Remove foot  
assembly from unit and turn over to access  
the brush roll belt.  
2.  
3
2. Remove three Phillips head screws to  
remove the belt cover.  
3. Locate broken belt.  
4. Replace belt.  
5. Place brush roll back into foot of unit.  
6. Replace the belt cover and secure with  
three screws.  
7. Attach foot assembly on unit.  
disposal of batteries  
WaRning:  
This product contains Nickel Metal Hydride (NiMH)  
rechargeable batteries. According to Federal and State  
regulations, removal and proper disposal of NiMH bat-  
teries is required. For removal of the batteries in your  
Lift-Off Floor & More see instructions below.  
TM  
if your lift-off floors & More is to be  
disposed of, the batteries should be  
removed and disposed of properly.  
3.  
1. iMPoRtant: Unplug Charger.  
2. Remove hand vac from unit and remove  
dirt cup from handle.  
3. Remove (5) Phillips head screws on the  
5 screws  
handle and cover.  
8
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Maintenance and care  
disposal of batteries continued  
4. Separate left and right cover.  
5. Remove the entire battery assembly from  
the cover.  
6. Remove (3) Phillips head screws between  
the motor and battery bracket.  
7. Pull the motor, PCB, fuse, and inner wire  
through the middle of the battery bracket,  
separating the battery bracket and single  
battery from the motor, PCB, and inner wire.  
8. Cut wires from the PCB and fuse to the  
battery bracket.  
9. Keep Battery Pack together – DO NOT  
separate individual batteries. For specific  
disposal instructions of batteries, please  
contact RBRC (Rechargeable Battery  
Recycling Corporation) 1-800-822-8837  
or visit www.rbrc.com.  
10.Discard remainder of product  
caution: Disconnecting the battery will  
destroy the appliance and void the war-  
ranty.  
Troubleshooting  
Vacuum wont turn on  
Possible causes  
Remedies  
1. Battery isn’t fully charged  
1. Charge battery. Follow charging battery instructions on page 5  
brush roll not turning  
Possible causes  
Remedies  
1. Brush roll is jammed  
2. Brush roll needs to be reset  
3. Broken brush roll belt  
1. Remove obstruction. Follow instructions on pages 7 and 8  
2. Follow instructions on page 8  
3. Follow instructions on page 8  
Vacuum cleaner has low suction  
Possible causes  
Remedies  
1. Dirt container is full  
1. Empty dirt container  
2. Dirt container is not installed properly  
3. Foot is loose  
2. Position container correctly and snap firmly into place  
3. Make sure foot is fully inserted into body of unit  
4. Follow filter instructions on page 7  
4. Filters need cleaning  
5. Filters need replacing  
replacement filters.  
9
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Troubleshooting  
Visible dirt escaping from vacuum  
Possible causes  
Remedies  
1. Dirt container is full of debris  
1. Empty dirt container  
2. Filter is missing or installed incorrectly  
3. Dirt container installed incorrectly  
2. Check filter for correct installation  
3. Position container correctly and snap firmly into place  
other maintenance or service not included in the manual should be  
performed by an authorized service representative.  
thank you for selecting a bissell product.  
Please do not return this product to the store.  
for any questions or concerns, bissell is happy to be of  
service. contact us directly at 1-800-237-7691.  
Replacement parts - BISSELL vacuum  
you may purchase parts by calling bissell consumer services or by  
visiting our website. below is a list of common replacement parts.  
Item  
Part No.  
Part Name  
1
52H6  
Filter assembly – set of 2  
2
3
4
5
6
7
203-1612  
203-1609  
203-1610  
203-1607  
203-1608  
203-1611  
Charging adapter plug  
Foot assembly  
Dirt cup assembly  
Brush roll belt  
Brush roll  
Hand vac assembly  
1
2
3
7
4
5
6
10  
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Warranty - BISSELL Lift-Off Floors & More Stick Vacuum  
This warranty gives you specific legal rights, and you may also have other rights which may  
vary from state to state. If you need additional instruction regarding this warranty or have  
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,  
telephone, or regular mail as described below.  
limited one year Warranty  
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product  
BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or  
products), at BISSELL’s option, free of charge from the date of purchase by the original  
purchaser, for one year any defective or malfunctioning part.  
See information below on "If your BISSELL product should require service".  
This warranty applies to product used for personal, and not commercial or rental service. This  
warranty does not apply to fans or routine maintenance components such as filters, belts, or  
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any  
other use not in accordance with the User's Guide is not covered.  
if your bissell product should require service:  
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your  
area.  
If you need information about repairs or replacement parts, or if you have questions about  
your warranty, contact BISSELL Consumer Services.  
Website or e-mail:  
Use the “Customer Support” tab.  
or call:  
BISSELL Consumer Services  
1-800-237-7691  
Monday - Friday 8 a.m. - 10 p.m. ET  
Saturday 9 a.m. - 8 p.m. ET  
or Write:  
BISSELL Homecare, Inc.  
PO Box 3606  
Grand Rapids, MI 49501  
ATTN: Consumer Services  
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES  
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT  
EXCEED THE PURCHASE PRICE OF THE PRODUCT.  
some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you.  
*eXcePtions and eXclusions fRoM tHe teRMs of tHe liMited WaRRanty  
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR  
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING  
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,  
ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED  
ABOVE.  
Some states do not allow limitations on how long an implied warranty last so the  
above limitation may not apply to you.  
11  
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 
Don't forget to register your product!  
Registering is quick, easy and offers you benefits over the lifetime of your product.  
You’ll receive:  
bissell Rewards Points  
Automatically earn points for discounts and free shipping on future purchases.  
faster service  
Supplying your information now saves you time should you need to contact us with  
questions regarding your product.  
Product support Reminders and alerts  
We’ll contact you with any important product maintenance reminders and alerts.  
special Promotions  
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!  
Visit www.bissell.com/registration now!  
BISSELL consumer services  
For information about repairs or replacement parts, or questions about your warranty, call:  
bissell consumer services  
1-800-237-7691  
Monday - Friday 8 a.m. — 10 p.m. ET  
Saturday  
9 a.m. — 8 p.m. ET  
Or write:  
BISSELL Homecare, Inc.  
PO Box 3606  
Grand Rapids MI 49501  
ATTN: Consumer Services  
Or visit the BISSELL website - www.bissell.com  
When contacting BISSELL, have model number of cleaner available.  
Please record your Model Number: ___________________  
Please record your Purchase Date: ___________________  
note: Please keep your original sales receipt. it  
provides proof of purchase date in the event of a  
©2011 BISSELL Homecare, Inc  
warranty claim. see Warranty on page 11 for details.  
Grand Rapids, Michigan  
All rights reserved. Printed in China  
Part Number 110-4369  
Rev 04/11  
Visit our website at:  
12  
w w w . b i s s e l l . c o m  
8 0 0 . 2 3 7 . 7 6 9 1  
 

Billion Electric Company Modem BIPAC 7100 User Manual
Bosch Appliances Home Security System LBB 4176 User Manual
Bosch Power Tools Saw 4100DG 09 User Manual
Brainboxes Network Card PM 121 User Manual
Braun Coffeemaker KF 610 User Manual
Brocade Communications Systems Router 16000 User Manual
Canon Printer MP 90 User Manual
Casio Clock 5163 User Manual
Casio Electronic Keyboard 7ES1A User Manual
CDA Cooktop RC 9000 User Manual